Vertical rod surface mount push bar

Locksmith San Antonio job at the "Howl at the moon" bar in downtown San Antonio

Recently we did a job at a San Antonio downtown bar "Howl at the moon".
The customer had a Von Duprin vertical rod push bar, 35 series (3527a to be exact) without the rods, so the doors stayed unlocked all the time!
We ordered and installed the surface mount vertical rods for this and it looks great. Please view the photos from this job.
Vertical rod surface mount push bar
Surface mount vertical rod
Vertical rod surface mount push bar

Bentley Key

Bentley Continental 2 doors Sport GT 2007


We are going to program a Bentley key by using the AR32 and the Tango systems.

The EEPROM we are going to program is inside the KESSY module.

As you can see in the photo the Bentley is using a VW KESSY module.

In the two doors Bentley Continental Sport GT the KESSY module is located under the carpet AT the driver side, not far from the pedals; you can feel it with your hand, you will feel a bump underneath the carpet.

To access the KESSY module, you need to remove the 4 bolts which are holding the driver’s seat. There are two bolts in the front and two bolts in the back. You do not remove the seat completely; there are several wire-harnesses connected at the bottom of the seat, so you want to be careful not to damage them. Just move the seat gently so you have enough room to remove the KESSY module from underneath the carpet.

Once you remove the KESSY module, locate the EEPROM. It is a 93C86, 8 pin chip located close to the largest chip, the microprocessor as seen in the following image:


The 93C86can be configured as 8 bit or 16 bit. Checking with an Ohm-Meter for a short between pins 5 and 6 of the chip can tell us how the chip is configured. If there is a short between pins 5 and 6 of the chip it is configured as 8 Bit. In our case, there was a short between pins 5 and 6 so the chip was configured as 8 bit.

Some recommend removing the chip completely from the board.  However, if you short the crystal, you should be able to read and program the chip in-circuit, without removing it from the board. We have confirmed it with the designer of the AR32.

If you are reading and programming the chip in circuit make sure to do the following:

  • Short the Crystal by soldering a wire across the 2 legs of the Crystal
  • Select device 93C86-8Bit from the AR32 library and press INS key (Insert).

If you are reading the device out of circuit select the device 93C86, not the 93C86-8Bit

Make sure all the switches are in the correct positions as shown on the computer display.

Once the file is saved (make sure you add the .bin extension) use the Tango to read the file.

Select the Bentley car from the Tango and load the bin file you read with the AR32.

If the Tango is able to read the bin file it means the file is good. If for any reason the file was not read correctly the Tango will display an error message saying it did not recognized the file.

After the Tango reads the bin file, select a key number (such as 3) place a transponder key inside the Tango slot and press W to write the file into the key (programming it). The Tango creates a new bin file and will ask to save the new bin file with a different name.

Now load the new bin file into the AR32 and write the new bin file back into the EEPROM. Place the KESSY module back in the car and start the car.

Access Control – Case Study


Access Control  Case Study

Project at glance:
Client: Greystar
Location: 2810 Hemphill Park, Austin Texas

S.A. Locksmith & Security in San Antonio Texas was awarded an access control job in Austin Texas. The job was to replace two old tele-entry access control systems which controlled access to elevators, doors, pedestrian and parking garage gates, about 20 in total, and held information of about 500 residents. The two old Access control and tele entry systems were:

1.      Old Linear tele entry and access control units.

2.      Old Sentex tele entry and access control units.

The old systems did not have enough memory to add additional residents to the database. In addition, the individual control panels were not connected to a network, so any deletion or addition of residents had to be done separately, at the location of each control panel, one at a time. There was no communication between the various panels!

In order to reduce cost, the requirements were to use the existing wires and to use the old readers, key fobs and transmitters, as much as possible. The project involved 3 parking garage gates, several pedestrian gates and several tele entry doors and gates.

As we will see, the requirement to use the old wiring was very challenging, since the new systems required more wires than the old system had.

Photos of the Old System


Old Sentex Access Control  


Old Sentex Access Control 


Old Linear Access Control

After evaluating the customer’s needs and the existing wiring, we came to the conclusion that the best solution would be to use the ‘Linear’ systems (now Nortek) and use their more advanced Tele-Entry systems.

We suggested using the AE-2000 plus systems for the tele-entry controllers and the AM-3 plus for the general door and gates controllers. These systems also include transmitters and option to add a remote receiver (the AE2000 plus also has an internal receiver). We used the Transmitters and receivers to control 3 parking garage gates.


Linear AE2000-Plus installed


Linear AM3 Plus


AM-CRI Expansion

Altogether we needed to use 10 control panel, 4 of them were Tele-Entry systems. In addition, we needed to use several Linear AM-CRI modules to extend the number of card readers each system can hold and support. We also added an AM-RRR remote radio receiver to the system to control an additional parking garage gate.

Remote adjustable range radio receiver PBUS accessory for outdoor applications, waterproof metal enclosure, connects to AM3Plus, AE1000Plus, or AE2000Plus access controllers

The Linear access control system can hold up to 8 panels (units) per network so we ended up using 2 networks: Network A and Network B.

It actually worked well, since the project was divided into two separate groups of buildings, so panels connected to Network A controlled one building complex, and panels connected to network B controlled a second building complex.

To make it convenient for programming the control panels from the offices, we ran wires from network A into an office in one building, and wires from network B into an office in the other building.



Wall Connection for Network A


Wall Connection Network B


Card Reader - Linear


AM-RRR-Remote Radio Receiver - Linear

Challenges we encountered:

The job became more complicated because of the requirement to use the existing wires of the old installation. Typically, there are many wires connecting the panels to card readers, to elevators, to electric strikes and to magnetic locks.

Because of the large size of the two building complexes, many of the panels were located far away from each other and on different floor levels.

One of the tasks we had to perform was to connect 2 groups of panels to two separate networks. 

In order to establish a network connection between the panels we needed 3 additional wires to connect between all the panels of each group.

This required running additional cables between the units which were located in different places and on different levels of the buildings.

In addition to running extra wiring for the two networks, we also needed to run several extra wires from some card readers to the AM-CRI.

Each Linear AE2000Plus or AM-3Plus supports 4 relays but only 2 readers. In order to add two more readers to each panel, we needed to use the Card Reader Interface box (AM-CRI) which can add 2 more readers.

The problem was that each reader had to have seven wires. In the old system, only 6 wires were connected to each card reader, so we were missing 2 wires for each AM-CRI expansion boxes. As a result, we needed to run additional wires between some card readers and AM-CRI units.

Programming the access control system:

The Linear (now Nortek) software is user friendly, it has great documentation and is very easy to program. All control panels can be programmed from the offices and adding/removing tenants is now a simple task.  

In conclusion: The Linear (now Nortek) access control system was a good choice for this project. S.A. Locksmith & Security was able to use much of the existing wiring of the old Sentex system and complete the job in a timely manner and save money to the client.


Programming 600 Series Code Mechanical Lock

Programming CL600 Code Mechanical Lock

Sam here again to show you how to program 600 Series Code Mechanical Lock!

The 600 series are heavy duty locks which allow on door code change.

Traditionally changing the code on mechanical locks required the lock to be removed from the door, but the CL600 allows changing the code without removing the lock from the door.

The CL600 lock is perfect for commercial applications such as  hospitals, schools and local authorities.

S.A. Locksmith & Security based in San Antonio, Texas can install and maintain the lock for your commercial locksmith needs.

Here are some specifications, as described by the manufacturer:

  • Heavy duty Codelock
  • Unique on door code change in seconds
  • Front cylinder change
  • High number of code combinations – over 8000
  • Full size lever handles
  • Code free option available
  • Mortice lock and mortice latch functions
  • PVD weather resistant, low maintenance finish
  • Back to Back available – provides coded access in both directions
  • Panic Kit options available – extra long spindle provided to work with most single point panic pads or bars
  • Lever handle or knob handle available on brushed steel finish
  • Tested to Grade 2- ANSI – A156.2
  • Codelocks Fire Kits can be fitted to latch locks

Your Commercial locksmith in San Antonio

S.A. Locksmith and Security (210) 348-3677

At S.A. Locksmith and Security we strive to provide you with only the most Commercial locksmith services in San Antonio, Texas. Our San Antonio locksmiths are trained to the utmost degree, providing promising efficiency and talent.

S.A. Locksmith and Security isn’t just like any other San Antonio Locksmith, we hold ourselves to a higher standard. With us, you’ll get polite and prompt responses from both the dispatcher and your assigned locksmith. Using Commercial, and up-to-date, locksmith equipment, S.A. Locksmith and Security vows excellence- and nothing less.

For any locksmith questions or concerns, or for information on locksmith products we carry, call us at (210) 348-3677

Tips to Secure your Home!

The 4 Tips you Must Know to Secure your Home!

S.A. Locksmith and Security (210) 348-3677

Is your home really safe? The 4 tips you must know for a secure home-

Being a locksmith in San Antonio I know there are many things one can do to increase the security of their home, business or car. It’s nice to remember that not every burglar in the world is at Ocean’s Eleven caliber, however any burglar is a threat.

Hiring a locksmith to install new locks or purchasing an alarm system are two ways one could upgrade their security. Aside from
purchasing new equipment one can increase their security without any purchases, exciting huh? Most locksmiths will tell you

security is also in the attitude, not only the fancy products you have. You have to have that motivation to get up and actually do
the work. Here are some easy home tips you can remember to help minimize the chance you become victim to an intruder.


During the night it is more difficult to spot people due to the darkness. Although many burglaries happen in broad daylight, I
have seen first-hand that many “go to work” during the dead of night. A smart locksmith tip is to illuminate the areas around your home. With a lit up property anyone walking on your property can easily be seen by you and your neighbors. This decreases the chance of getting robbed while increasing the chance of your intruder being seen before the damage is done.

Keep tools inside

Often time’s household members will leave tools- screwdrivers, hammers, wrenches, etc. – outside their home, most often by
the garage. Professional locksmiths say that by doing this, you are giving your intruder some useful tools to use to break in. By
remembering to bring in any tools around your property you can vastly limit the success of your intruder.

Hidden keys

This is probably the most occurring problem we hear about as locksmiths. We want to have easy access to our hidden home
key; therefore we keep it very proximate to the front door. Whether it’s under the doormat, above the door frame or inside the flower pot, these burglars know where to look. Think of your hiding spot and then think again. This is basically giving the burglar
the open invite to rob you. Tell yourself you need to hide the key further away from your door, and in a way better hiding spot.

Lighting, hiding tools and HIDING the hidden key are three easy and quick steps you can take today to upgrade your home’s security.
Contact a locksmith in San Antonio for more security tips. San Antonio is a big city, make sure you do all you can do protect your property.

Do you already follow these tips? Have they worked for you? Feel more than welcomed to share any comments or stories with
us, as I am very eager to read them.

Parking Safely in Public

Parking Safely in Public

S.A. Locksmith and Security (210) 348-3677

White-van-2-with-sign-2-extractedFor a big city like San Antonio security should always be on your mind when doing anything- and parking is no exception. When leaving your car unattended there are always risks to look out for. This is why parking safely in public is essential.

When parking your car there are several things to keep in mind so you can feel at ease. Typically you want to avoid attention from car thieves at all times. You want to detract anything that highlights your car.

Safe Parking- Illumination

Parking safely in public areas try and find a parking spot that is lit up. Park under a street lamp or next to a lit up building to increase your chances of thwarting a car thief.
The minute a thief sees your car is lit up like the empire state
building he’ll most likely move onto a car parked in darkness.

Safe Parking- Away from exits

When parking in garages or parking lots make an effort to part as far away from the exit/entrance as possible.
Normally a car thief will try to go for a car closest to the exit for the quickest escape. A car parked next to the exit is very attractive to a car thief.
For safe parking make sure to park as far away as you can from the exit. When a thief sees your car he’ll count it as too much work and too high of a risk, and most likely move on.

Safe Parking- Camouflage

Another good tip for parking safely in public is to try parking between a group of cars. A car on its own stands out to a car thief so by parking between a group of cars you can camouflage your vehicle.
A car parked alone will cause a car thief to put his direct attention towards it.

Stop Losing Your Car Keys- S.A. Locksmith and Security

S.A. Locksmith and Security (210) 348-3677 

It’s an issue some of us face every morning before work. You get dressed, eat your breakfast and head for your door- only to realize you’ve lost something. What’s that? Oh that’s right, your keys. Sound familiar? Being more organized is one obvious solution, but for some of us that’s asking a lot.

How to stop losing your car keys?

Designate only one area for your keys- When we toss our keys on the table, and the bed, and the kitchen counter, etc. it gets way too confusing when trying to locate them. With so many possible spots they could be hiding in you could find yourself searching for hours. By designating one area- a hook by your door or on a bookshelf in the living room- you eliminate countless amounts of possible hiding spots, limiting your search time.

Remembering- It can be easy for some to forget to put their keys away immediately as they enter their home- even locksmiths. Keys can end up remaining in your pockets for some time before you finally put them away. Place an eye-catching colored bowl by your front door- within your immediate line of sight. Hopefully, the color will attract you and remind you to place your keys in the bowl AS SOON AS you enter your home.

Purchasing a key ringer- A useful gadget when trying to locate a lost set of keys. A key ringer rings (duh) allowing you to find it with your ears. They aren’t expensive and are extremely clutch in a rush, much faster than calling a locksmith. This is another effortless way to keep track of your beloved key-ring.

With these easy tips you can spend less days searching for your lost car keys and more days being on time for work. Of course if you need a new copy of the lost key give S.A. Locksmith and Security a call. If you liked these helpful tips wont you give this post a like, and maybe comment with some of your own tips? I’d be more than happy to read what you got.

S.A. Locksmith & Security: Car Lockout

S.A. Locksmith & Security: Car Lockout

Call us now at (210) 348-3677 to speak with a San Antonio locksmith professional.

If there’s one thing to worry about here in San Antonio it’s the heat. With the strong possibility of heat stroke staying cool is a top priority.
In the event that you experience a car lockout it is important you have someone in mind that you can call for help. With this heat a car lockout is a real emergency and you need people to respond accordingly.
This is why you need to call us at S.A. Locksmith & Security for all of your locksmith needs! We can arrive out to you in less than 25 minutes- even sooner if the day is especially hot.
S.A. Locksmith & Security
When you call us at S.A. Locksmith & Security for a car lockout you will receive only professional and prompt services. We can send out a locksmith to you wherever you are, and in a matter of minutes you will be on your way again!
Standing out in the heat for a long period of time can be fatal, especially during a car lockout- be prepared and have a locksmith in mind before you are in urgent need of one! This can save your life!
For any emergency, save our number so you can be prepared!

Call us now at (210) 348-3677 to speak with a San Antonio locksmith professional.

SA Locksmith and Security: What to do after buying a house

S.A. Locksmith & Security

Locksmith San Antonio – The 3 MOST IMPORTANT steps you must take after purchasing a new home
Moving to a new city like San Antonio can be challenging for many. For some it’s an exciting experience, but for others it brings up many stressful situations- one of those being security.
Being a locksmith in San Antonio I know moving into a new home can bring uneasy thoughts to mind, especially when security is your priority.
Here are the three steps everyone should take when moving into a new home- whether it is in the same city as your old home or not- that can save you more than just a heartache.
Step One: The first step anyone should take when moving into a new home is to call a locksmith. They know the steps to take and how to take them.
For example, a San Antonio locksmith can meet you at your new home and assess your home’s security as well as offer professional security advice. A locksmith is your best friend when it comes to protecting your house- utilize them!
Step Two: you should take is to change out all your locks! This is a very important (maybe the most important) step you should take immediately.
You never know who else has the exact same set of keys that you do. By replacing all the locks in your home you can make sure you are the only person with keys to your home.
Any San Antonio locksmith has the ability to replace your locks. It is a relatively quick and painless process that really separates the secure from the non-secure. Just the peace of mind it can bring you is worth the extra effort.
Step Three: After you’ve contacted your locksmith and had your locks changed its time for the final step in new-home security. It’s time for you to really learn about your surroundings- drive around the neighborhood, meet some of your neighbors or assess your property for easy break-in points.
This is a tip I give out to many new buyers seeking out a locksmith in San Antonio. In order to fully be secure one must acquire knowledge of their surrounding area.
By taking a “tour” around your neighborhood you can get a better insight at the type of activity that goes on there. Keep a look out for suspicious people or situations.
Meeting your neighbors is a great way to improve your security. Typically a friendly neighbor has nothing to hide and by taking the initiative to meet your new neighbors you are presenting yourself as a safe resident- a resident they should never have to worry about.
This also allows you to discover which of your neighbors strikes you as normal or suspicious- security is all about knowing your battlefield.
Finally, by assessing your property you can discover areas that could offer aid or assistance to an intruder.
Planting thorn bushes or cactus by windows is a good way of blocking them off as possible break-in points.
Remove any excess shrubbery or bushes that could offer hiding or camouflage spots at night. Keeping a low trimmed lawn removes many possible hiding spots.
Lastly, install motion or standard lights around your property so any intruder has a much higher chance of being spotted by you or a neighbor- and a neighbor is more likely to assist you if they like you and trust you, which is why I say to take the initiative and introduce yourself early on.
Moving into a new home should be an exciting moment in your life- not a scary one. By taking the initiative you set yourself up for a great safety situation.
“Keep your friends close and your enemies closer” is a phrase that locksmiths in San Antonio live by. You need to be as knowledgeable about your surroundings and neighbors as you can to ensure you’re never left surprised or off-guard.